HH-THC06硅烷化总烃柱 HJ 604-2017 环境空气 总烃、甲烷和非甲烷总烃的测定 直接进样-气相色谱法

名称：硅烷化总烃柱

材质：钝化不锈钢管

规格：0.6m*1/8

型号：HH-THC06

应用：HJ 604-2017 环境空气 总烃、甲烷和非甲烷总烃的测定 直接进样-气相色谱法

1 适用范围
      本标准规定了测定环境空气中总烃、甲烷和非甲烷总烃的直接进样-气相色谱法。
      本标准适用于环境空气中总烃、甲烷和非甲烷总烃的测定，也适用于污染源无组织排放监控点空气中总烃、甲烷和非甲烷总烃的测定。

当进样体积为1.0ml时，本标准测定总烃、甲烷的检出限均为0.06mg/m³（以甲烷计）, 测定下限均为0.24 mg/m³（以甲烷计）；非甲烷总烃的检出限为0.07mg/m³（以碳计），测定下限为0.28 mg/m³（以碳计）。

2 规范性引用文件
      本标准引用了下列文件或其中的条款。凡是不注日期的引用文件，其有效版本适用于本标准。
      HJ 194 环境空气质量手工监测技术规范
      HJ 664 环境空气质量监测点位布设技术规范（试行）
      HJ 732 固定污染源废气挥发性有机物的采样气袋法
      HJ/T 55 大气污染物无组织排放监测技术导则

3 术语和定义

      下列术语和定义适用于本标准。

3. 1

      总烃 total hydrocarbons (THC)

指在本标准规定的测定条件下，在气相色谱仪的氢火焰离子化检测器上有响应的气态有机化合物的总和。

3.2

      非甲烷总烃 nonmethane hydrocarbons (NMHC)

指在本标准规定的测定条件下，从总烃中扣除甲烷以后其他气态有机化合物的总和（除非另有说明，结果以碳计）。

4 方法原理

将气体样品直接注入具氢火焰离子化检测器的气相色谱仪，分别在总烃柱和甲烷柱上测定总烃和甲烷的含量，两者之差即为非甲烷总烃的含量。

浩瀚色谱（山东）应用技术开发有限公司参照《环境空气总烃,甲烷和非甲烷总烃的测定直接进样-气相色谱法》HJ604-2017来测定总烃,甲烷和非甲烷总烃.对仪器条件进行优化,得出总烃的检出限为0.007mg/m3,甲烷的检出限为0.013mg/m3,非甲烷总烃的检出限为0.015mg/m3,研究0.453-7.21mg/m3浓度的甲烷标气,得出总烃的校准曲线方程为y=12,948.8244 x+742.7768;甲烷的校准曲线方程为y=12,409.5958 x+416.4558;该方法操作简单,分析速度快,实验结果满意.


HJ 604-2017 Ambient Air Determination of Total Hydrocarbons, Methane and Non-Methane Total Hydrocarbons Direct Injection-Gas Chromatography
HJ 604-2017 Ambient Air Determination of Total Hydrocarbons, Methane and Non-Methane Total Hydrocarbons Direct Injection-Gas Chromatography Details:

Name: Silanized Total Hydrocarbon Column

Material: Passivated stainless steel tube

Specifications: 0.6m*1/8

Model: HH-THC06

Application: HJ 604-2017 Ambient Air Determination of Total Hydrocarbons, Methane and Non-Methane Total Hydrocarbons Direct Injection-Gas Chromatography

HJ 604-2017 Ambient Air Determination of Total Hydrocarbons, Methane and Non-Methane Total Hydrocarbons Direct Injection-Gas Chromatography
1 Scope of application
      This standard specifies the direct injection-gas chromatography method for the determination of total hydrocarbons, methane and non-methane total hydrocarbons in ambient air.
      This standard applies to the determination of total hydrocarbons, methane and non-methane total hydrocarbons in ambient air, and also applies to the determination of total hydrocarbons, methane and non-methane total hydrocarbons in the air at monitoring points of fugitive emissions from pollution sources.

When the injection volume is 1.0ml, the detection limit of this standard for the determination of total hydrocarbons and methane is 0.06 mg/m3 (calculated as methane), and the lower limit of detection is 0.24 mg/m3 (calculated as methane); non-methane total hydrocarbons The detection limit is 0.07 mg/m3 (calculated by carbon), and the lower limit of determination is 0.28 mg/m3 (calculated by carbon).

2 Normative references
      This standard refers to the following documents or clauses thereof. For undated references, the valid edition applies to this standard.
      HJ 194 Technical Specification for Manual Monitoring of Ambient Air Quality
      HJ 664 Technical Specifications for Layout of Ambient Air Quality Monitoring Points (Trial)
      HJ 732 Sampling air bag method for volatile organic compounds in waste gas from stationary pollution sources
      HJ/T 55 Technical guidelines for monitoring fugitive emissions of air pollutants

3 Terms and Definitions

      The following terms and definitions apply to this standard.

3.1

      total hydrocarbons (THC)

Refers to the sum of gaseous organic compounds that respond on the hydrogen flame ionization detector of a gas chromatograph under the measurement conditions specified in this standard.

3.2

      nonmethane hydrocarbons (NMHC)

Refers to the sum of other gaseous organic compounds after deducting methane from the total hydrocarbons under the measurement conditions specified in this standard (unless otherwise stated, the results are in carbon terms).

4 Principles of the method

The gas sample was directly injected into a gas chromatograph with a hydrogen flame ionization detector, and the contents of total hydrocarbons and methane were measured on the total hydrocarbon column and the methane column, respectively, and the difference between the two was the content of non-methane total hydrocarbons.



Haohan Chromatography (Shandong) Application Technology Development Co., Ltd. refers to "Determination of Total Hydrocarbons, Methane and Non-Methane Total Hydrocarbons in Ambient Air Direct Injection-Gas Chromatography" HJ604-2017 to determine total hydrocarbons, methane and non-methane total hydrocarbons. For the instrument The conditions are optimized, and the detection limit of total hydrocarbons is 0.007mg/m3, the detection limit of methane is 0.013mg/m3, the detection limit of non-methane total hydrocarbons is 0.015mg/m3, and the detection limit of the research is 0.453-7.21mg/m3 The calibration curve equation of total hydrocarbons is y=12,948.8244 x+742.7768; the calibration curve equation of methane is y=12,409.5958 x+416.4558; the method is simple to operate, fast to analyze, and the experimental results are satisfactory.